|
The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,763. Welcome to our newest member, mtan1446
EngravingForum.com -
Domain since Feb 7, 2003
Graver Video Conferencing is empty Join now!
|
|||||||
| ENGRAVING TOOLS - Paypal accepted | Classes | Glossary | Feedback | Tips | Sharpening | Bulino | Videos | Forum Policies |
 |
|
|
Thread Tools |
|
#1
07-16-2008, 12:41 PM
|
|||
|
|||
Classic arrived today
After 3 years of putting it off I ordered a classic airgraver. Today it arrived, I am stuck here at work but cant wait to get it to the shop and try it out.
Thanks Steve 
|
|
#2
07-16-2008, 01:01 PM
|
||||
|
||||
|
Re: Classic arrived today
James
Look in the 'AirGraver Info' section for my post on the Box O' Happiness - I just finished using part of my lunch hour to use my Classic. 
|
|
#3
07-16-2008, 02:03 PM
|
|||
|
|||
|
Re: Classic arrived today
Hi Steve,
Thats a great set-up. I will probably end up with something along those lines. Thanks Jim
|
|
#4
07-16-2008, 04:22 PM
|
||||
|
||||
|
Re: Classic arrived today
The great thing is that I added a 'monster cup-holder' to my bench so it's easy to use my Classic there as well.
If you go to your local Home Depot type store, get a 4" PVC Cap - nice big rounded cup sort of thing. Get an adapter for 4" to 3" - it'll slide into the cap snugly. The one I got had a ring inside I had to scrape down with a knife to get a 20oz cylinder to fit. Drilled two holes in the cap and screwed it onto my bench (I stood the cylinder in the assemblage and moved it up and down to find where I wanted it first, of course). With my big hands it was a bit tricky but a stubby screwdriver and some determination got the job done. Slid the adapter in about 1/2" and now I can just set the cylinder into it's little holder and work away under my scope. Eventually I'll get around to having a set of gravers that stay on my bench but for now I just transfer the one set back and forth - have to move them to get the cylinder out of the bottom anyway.
|
|
#5
08-10-2008, 05:07 AM
|
|||
|
|||
|
Re: Classic arrived today
Well thats a great idea. I am using a paintball HPA tank, and it just lays there on the floor, I knew there was a better solution. I have got to say using the HPA is great, no compressor noise.
Thanks Jim
|
|
#6
08-10-2008, 10:35 PM
|
||||
|
||||
|
Re: Classic arrived today
Hi Jim, Good deal! Have you been making a few chips with it? What are you using for a regulator with the HPA tank?
__________________
__________________________________ Steve Lindsay AirGraver.com EngravingArtist.com
|
|
#7
08-11-2008, 06:38 AM
|
|||
|
|||
|
Re: Classic arrived today
Hi steve,
I have been making some chips, its a great tool. Wish I had more time to play with it. It is amazing how bright the cuts are. I am using the regulator from the Kobalt portable compressed air regualtor kit sold at lowes. It seems to work fine. Jim
|
|
#8
08-11-2008, 09:41 AM
|
||||
|
||||
|
Re: Classic arrived today
I didn't know that Kobalt had a HPA air regulator. I'll hunt for it. Do you know, can you get more time from one of the hpa paintball tanks or from a 20oz paintball co2 tank?
__________________
__________________________________ Steve Lindsay AirGraver.com EngravingArtist.com
|
|
#9
08-11-2008, 11:04 AM
|
|||
|
|||
|
Re: Classic arrived today
Hi Steve,
The Kobalt regulator if for CO2. But since I am using a paintball HPA tank, the air is pre-regulated down to CO2 levels, I think around 835psi. I believe that you will get slightly more time from the HPA. You can also get larger tanks. See regulator here. http://www.lowes.com/lowes/lkn?actio...735-J-6901-100 Jim
|
|
| Bookmarks |
| Thread Tools | |
|
|
