|
The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, AnicaLin
EngravingForum.com -
Domain since Feb 7, 2003
Graver Video Conferencing is empty Join now!
|
|||||||
| ENGRAVING TOOLS - Paypal accepted | Classes | Glossary | Feedback | Tips | Sharpening | Bulino | Videos | Forum Policies |
 |
|
|
Thread Tools |
|
#1
08-05-2016, 09:58 AM
|
|||
|
|||
Extreme Newbie
Hello Everyone!
My name is Kirsten Hengstberger. The GRANDbabies call me "Mama Cheez" because they can't quite pronounce "Hengstberger" yet.  So, for some crazy reason, I started experimenting with etching glass with my Dremel tool, which was a hand-me-down from my brother-in-law after he passed away in 2011. Haven't touched the thing until now. I must honestly say, I've been too intimidated to touch it. Recently, I found Lesley Pyke on youtube and became instantly NOT afraid anymore. And, since the fear is gone, I have been doing research and ultimately ended up at this amazing forum. I am so excited to learn everything I can! I am 51 years young and a stay-at-home wife. (And "mama" to five dogs and a cat.) I would ultimately like to make some extra cash, hopefully. What can I learn here? What can y'all teach an ol' dog like me?  PLEASE! DO TELL!! Thanks for letting me be a part of this community! 
|
|
#2
08-05-2016, 02:22 PM
|
|||
|
|||
|
Re: Extreme Newbie
The one thing you can learn to start with is to dump the Dremel tool and the glass. Neither has anything to do with what is practiced here. Then you will need to acquire a whole nuther set of tools. Take a look at the advice given to the other newbies in the Who's Who forum. They are full of what you are looking for.
__________________
Dave Kanger Some men are wise, some are other wise.
|
|
#3
08-06-2016, 07:51 AM
|
||||
|
||||
|
Re: Extreme Newbie
Welcome MamaCheez!
 There are other glass engravers on the forum. Here are previous threads you may enjoy: http://www.engravingforum.com/showthread.php?t=3894 http://www.engravingforum.com/showthread.php?t=7650 http://www.engravingforum.com/showthread.php?t=8130 http://www.engravingforum.com/showthread.php?t=9410 http://www.engravingforum.com/showthread.php?p=93787 The process of hand engraving metal is usually thought of as cutting by shearing the metal with a single pointed graver. Metal and glass can be ground (where the material isn't "cut" but is ground away with a an abrasive like diamond on a rotary bur), however the nature of this method it isn't possible to achieve the same level of detail as a single point graver. A good example of metal being hand engraved with a graver is to look close at the portrait on paper currency. There is longer definition of what hand engraving with a graver is along with photos at this page link: www.engravingschool.com Tools for hand engraving with a graver can be done with or without aided power. Here is a thread about manual push engraving: Inexpensive way to give it a try http://www.engravingforum.com/showthread.php?t=4
__________________
__________________________________ Steve Lindsay AirGraver.com EngravingArtist.com
|
|
#4
08-07-2016, 04:09 AM
|
|||
|
|||
|
Re: Extreme Newbie
Quote:
Please dont call yourself an "ol dog"a lot of us are past your age. I can Welcome you to The Engraving Forum. SE 
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
|
|
| Bookmarks |
|
|
