Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,762. Welcome to our newest member, Katherine
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 09-13-2015, 09:15 PM
Giordano&Dee Giordano&Dee is offline
Copper
 
Join Date: Sep 2015
Location: Minneapolis, MN
Posts: 1
Default Lindsay Maintenace

I am debating between the GRS GraverMach AT and the Lindsay Classic Airgraver. I am leaning towards the Lindsay. However, my one concern is the maintenance. I have heard (and I mean no disrespect) that it is a bit finicky to get it to run properly. Has anyone else found this to be true? What sort of yearly maintenance should I expect to do on the handpiece?

Also, in the description for the Classic Airgraver, it states "Rapid 3/32" square graver change without collets." Personally, I prefer using a quick change system. What are your opinions on the quick change extensions? Do they impact the performance of the Airgraver?

Your thoughts are greatly appreciated.
Reply With Quote
  #2  
Old 09-13-2015, 10:36 PM
Soco's Avatar
Soco Soco is offline
Platinum
 
Join Date: Jul 2009
Location: Tx
Posts: 264
Default Re: Lindsay Maintenace

Quick change only makes the over all length longer, no real changes translate to graver to metal feel in my experience using them.. hovever.. you can quick change without them if the backs of the gravers are the same shape and size.

I think I may have given my classic a swab inside once in a couple years.. there was nothing going on with it, I was more curious to see the piston and felt like maybe I should.

I've used 3 of the GRS systems.. and love most of their tools. Except when it comes to the powered graver systems. Id never swap my Classic for one.. ever.
If possible try them before buying.. if not watch videos and listen to the difference. that sound translates to performance and feel.
anyway theres 2cents
Good luck.
Reply With Quote
  #3  
Old 09-13-2015, 10:38 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Lindsay Maintenace

Hi Giordan, It is necessary to keep oil out of the bore and piston. The manual describes that if you notice the tool does not idle as fine as it used to or stopping, it is time to clean it. This is done by removing the handle, dumping the piston in your hand and using alcohol on a q-tip to swab out the bore, wipe off the piston with alcohol and reassemble.

Yes, with 3/32" square gravers in the Classic it can be setup for quick change without collets. If you would like to use collets though there are the quick change extensions made for the Classic. It is method 5 that I have included below from an earlier post about the various methods of holding gravers in the Classic.

Quote:
Originally Posted by Steve Lindsay View Post
The Classic and PalmControl are already set up to do quick change without collets by only using 3/32" square gravers themselves.

Below are the methods in the manual about changing gravers in the Classic and PalmControl. If switching a lot, I use method #1 (no collects needed) or method 2 is also quick. For work on the knives I didn't change gravers very often and so I would use method 3.

1: Slip a graver in and out of the tool hole. Gravers are held from rotating or falling out of the tool hole because of the oring, yet they may be pulled out or pushed in easily. This works best with 3/32" square shank gravers. To prepare the tool, insert a 3/32" square graver and leave the setscrew slightly backed off from the surface of the graver. The screw acts as an index in this way and the friction of the O-ring in the front of the tool hole prevents the graver from falling out. Once the setscrew is set, it does not need to be adjusted to change gravers.

2. Utilizes a thumb screw for a more secure grip. This will work with any shank graver (round or square) under .133" in size. Remove the setscrew and use the knurled thumbscrew in its place. The graver can be tightened down for a more secure grip than #1.

3. The third way to use the tool holder is with a set screw and wrench. This will provide the most secure hold. It will work with any shank graver (round or square) under .133" in size.

4. The fourth method is to remove the setscrew or thumb screw from the AirGraver's nose completely, and just slip the 3/32" square graver shanks in/out. It is similar to #1", but with the set screw completely removed. The rubber o-ring is then all that is used to hold the graver in the tool hole.

5. Last method is using the quick change extensions for the Classic. They provide extra length for large hands or if wanting to get more use from a short graver.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #4  
Old 09-14-2015, 05:53 PM
johnpilk johnpilk is offline
Gold
 
Join Date: Oct 2007
Posts: 176
Default Re: Lindsay Maintenace

the classic works fine for me.i,ve been using about 9 yrs now . had rebored and a tungsten piston made for it . i use a oil compressor like steve has on the tool list silent air . i have 2 filters on the tank and another on the set of guages at a higher level, above . i have cleaned the tool as prescribed several times internally with an alcohol swab . it works perfectly as new the day i got it back from the rebore. it did not idle as good as it did lately a couple weeks ago.it was not the way i was cleaning it . i looked down the bore with a bore light and saw a fine damp ring where the outer diameter of piston contacts the forward edge of the barrel. so i cleaned it again , this time bending the q tip at a 45 degree angle and rotating the barrel around it. after several yrs. the very light film of oil and air had made a very tacky spot between the piston and the hammering edge making it stick and not idle well . i cleaned this and it idles as good as the day he sent me the new rebore and i remember as he said that the rebore and new liner would idle to the point to where you couldn,t hear or feel it . it does. i run a tungsten piston all the time at 80 psi . john
Reply With Quote
  #5  
Old 09-14-2015, 07:07 PM
dcurrie911 dcurrie911 is offline
Steel
 
Join Date: Nov 2011
Location: Bushnell, FL
Posts: 41
Default Re: Lindsay Maintenace

I have been engraving for only two year with a Lindsey PC and have only tried a GRS once for about 15 minutes so I am far from an expert. But I would not hesitate to recommend Steve's PC to my grandma! And you NEVER disappoint grandma.

Dan
Reply With Quote
  #6  
Old 09-15-2015, 02:11 AM
Phil Coggan Phil Coggan is offline
Platinum
 
Join Date: Apr 2008
Location: South Wales
Posts: 899
Default Re: Lindsay Maintenace

Steve's PC is as far as I am concerned the ultimate for engraving, I must admit that I have'nt tried anything else, but that said, I don't need to.

I have had the tool now for around four years, Steve would know the actual dates. I have used it continuously and probably more than others for this period, I have never stripped it for cleaning as there is no need to, but maybe in the next four years The only thing I have done is cut and re-seat the main air tube fixed to the back which can split with continuous use.

To be honest, I wouldn't be without it

Phil
Reply With Quote
  #7  
Old 09-15-2015, 09:21 AM
JJ Roberts's Avatar
JJ Roberts JJ Roberts is offline
Platinum
 
Join Date: Apr 2006
Location: Northern Virginia
Posts: 2,070
Default Re: Lindsay Maintenace

I clean my PC every two weeks and also drain my air compressor Lindsay tools are the best and easy to maintain,students are amazed when they get to engrave with any of the four Lindsay handpiece's I have in my shop where I teach in Manassas,Va. J.J.
Reply With Quote
  #8  
Old 09-15-2015, 04:27 PM
surgicalshot surgicalshot is offline
Steel
 
Join Date: May 2013
Location: Nebraska
Posts: 17
Default Re: Lindsay Maintenace

The Classic Airgraver has so few moving parts, that very little could even go wrong with it. You can adjust the idle with a slight turn of the air valve on the regulator. You can have the idle so low you can hardly feel it or as strong as you want. I have taken the cap off to swab mine out, but it was not because it was not working. By looking inside you can see there is very little to go wrong.

The Classic already has a quick release built into it. If you need some extended length you can then add the removable quick release. I really thought I would need some also. I have not used one yet and now have no reason to need them.

The Airgraver is so smooth at starting and stopping. I purchased mine and kicked myself for not getting it several years sooner. It was just as exciting as when we got our first color TV - It changed the world!!!

I would highly recommend the airgraver to anyone whether they are just learning or have been engraving for several years. I have not ever regretted it even for a split second, other then regretting I didn't get it sooner. I THINK YOU WILL LOVE IT.

Best Wishes!
Kirk
Reply With Quote
  #9  
Old 09-15-2015, 04:35 PM
Jahn Baker's Avatar
Jahn Baker Jahn Baker is offline
Steel
 
Join Date: Mar 2008
Location: Cottonwood, AZ - USA
Posts: 46
Default Re: Lindsay Maintenace

Giordano&Dee, Welcome to the forum. I switched from a GRS system and have been using the classic system with the foot control for a few years now and am totally happy with it. It is simple, straightforward and extremely well built. The Lindsay gravers slide into place and can be changed in an instant as needed without any additional fittings. This also facilitates quicker and more consistent sharpening with the Lindsay templates, and believe me you want to be able to sharpen easily.
__________________
Jahn
Reply With Quote
  #10  
Old 09-16-2015, 05:38 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: Lindsay Maintenace

Quote:
Originally Posted by Giordano&Dee View Post
I am debating between the GRS GraverMach AT and the Lindsay Classic Airgraver. I am leaning towards the Lindsay. However, my one concern is the maintenance. I have heard (and I mean no disrespect) that it is a bit finicky to get it to run properly. Has anyone else found this to be true? What sort of yearly maintenance should I expect to do on the handpiece?

Also, in the description for the Classic Airgraver, it states "Rapid 3/32" square graver change without collets." Personally, I prefer using a quick change system. What are your opinions on the quick change extensions? Do they impact the performance of the Airgraver?

Your thoughts are greatly appreciated.

HI

Firstly Welcome To The Engraving Forum Giordano&Dee.

I was once in a similar situation as yourselves.

I have had the classic airgraver for sometime now and It has not needed any maintenance so far.Just did what the instructions manual said in setting it up and started engraving with it,It is easy as that.It has been approx. a couple of years and it is still going fine.

On that note I acquired the Artisan Airgraver approx. 4-5 years ago (before i got the classic airgraver) and I do all the heavy cutting with the Artisan,and I have so far only switched the pistons,stainless piston to tungsten or the other way.But it has not needed any maintenance till now except while changing pistons I have clean the bore with a dry cotton bud ,which hardly takes a couple of minutes.

The reason I mentioned the Artisan airgraver is that both the classic and the artisan use similar method or technology except that the Classic airgraver has a variable stroke.

You will only need an air compressor and you are off.

I wish You All The Best
SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #11  
Old 09-16-2015, 09:24 AM
speeedy6 speeedy6 is offline
Copper
 
Join Date: Oct 2014
Location: Knoxville , Tn.
Posts: 9
Default Re: Lindsay Maintenace

I'm a complete amateur and have an Artisan . I had a problem with it a few months ago that was probably more my fault and Steve jumped in there and solved the problem with actions so far above what I thought should happen that I base how I treat customers of mine like that now. So, Steve not only puts out a machine that works like a clock but , gives life lessons too !
As far as the quick change collets go, I thought I needed one for each graver to efficiently go from one graver to another but now, I use one collet with a thumbscrew and I can probably change tips as fast or faster.
Steve's customer service is second to none !
Reply With Quote
  #12  
Old 09-18-2015, 09:48 AM
davidonthebeach's Avatar
davidonthebeach davidonthebeach is offline
Gold
 
Join Date: Aug 2012
Location: Santa Barbara, California
Posts: 153
Default Re: Lindsay Maintenace

I have used my Lindsay Palm Control daily for going on 3 years. It is the finest, most trouble free piece of equipment I have ever had. Love it!
__________________
Best regards,
David
http://dsengraver.com
Reply With Quote
  #13  
Old 09-18-2015, 11:16 AM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,360
Default Re: Lindsay Maintenace

Reply With Quote
  #14  
Old 09-19-2015, 04:03 PM
Eric Watson Eric Watson is offline
Platinum
 
Join Date: Mar 2007
Posts: 208
Default Re: Lindsay Maintenace

Maintenance is easy and the customer service outstanding. I own a couple systems one sits on a shelf and the Lindsay is the only one used.

Eric
Reply With Quote
  #15  
Old 09-20-2015, 02:57 PM
Toad Toad is offline
Gold
 
Join Date: Mar 2008
Location: Vermilion, Ohio
Posts: 123
Default Re: Lindsay Maintenace

Maintaining the Lindsay. Feed it clean air(all air powered engravers need this). Clean the bore out once in a blue moon with a cotton swab and alcohol.
Reply With Quote
  #16  
Old 09-20-2015, 04:59 PM
carl bleile's Avatar
carl bleile carl bleile is offline
Platinum
 
Join Date: Mar 2008
Location: cincinnati,ohio
Posts: 385
Default Re: Lindsay Maintenace

I had the GRS with 6 hand pieces to do different types of cutting. Years ago got the Lindsay classic, and haven't used anything else since. one hand piece does it all and no extra boxes to hook up to. If anything goes wrong with the GRS hand piece or the power box and it does you have to send the whole mess back to the corporation and hope for the best. The Lindsay quick change works very well it just adds a little length which I find comfortable in my hand.
Reply With Quote
Reply

Bookmarks

Tags
airgraver maintenance, quick change collects


Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 06:23 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.